Giỏ hàng rỗng

Tổng tiền: 0 VNĐ
0

Máy Đo Hiệu Chuẩn Takikawa TMG

Mã sản phẩm: TMG-05, TMG-10, 05B, 06B

Thương hiệu: Takikawa Engineering

Xuất xứ: Nhật Bản

Liên hệ: để đặt hàng

khách hàng đã mua sản phẩm này

Calibration gauge /Gauge pin Unit /Fixture for TM/TMS Series Calibration gauge

Gauge outside dia.(mm) Gauge pin Unit Accuracy
Φ1.0 TMG-10 ±1μm
Φ0.5 TMG-05 ±1μm

*)Φ0.5mm or less can be made for Φ0.1mm. Gauge pin Unit Fixture and Gauge pin Unit

Model Use for gauge pin Unit Model of Gauge pin Unit Fixture
TM-1000S TMG-05 01
TM-1003 TMG-05 02
TM-1000XY TMG-05 03
TM-1004 TMG-05 04
     
TM-1100XY TMG-05 05B
TM-1003W TMG-05 06B
TM-1104W/TMS-1104W TMG-05 07B
     
TM-503W TMG-01 16B
     
TM-3001W TMG-10 08B
TM-3002W TMG-10 09
TM-3004W TMG-10 10B
TM-3008W TMG-10 10B
TM-3016W TMG-10 10B
     
TM-4001/4001W TMG-10 ----
TM-4002 TMG-10 12B
TM-4002W TMG-10 17
TM-4004 TMG-10 13B
TM-4008 TMG-10 13B
TM-4016 TMG-10 13B
     
TM-6004 TMG-10 14B
TM-6008 TMG-10 14B
TM-6016 TMG-10 14B
     
TM-7003 TMG-10 15B
TM-7009 TMG-10 15B
TM-7012 TMG-10 15B

 

Example of calibration method(TM-3004W) This Detector is already provided a calibration before the delivery.  However, if another calibration is required in order to assume the detecting sensitivity at the examination, you have to follow the method mentioned below to make it correctly, using a calibration gauge pin unit. (Calibration Gauge Pin Unit No.TMG-10 and Gauge Pin Unit Fixture No.10B are the optioned items).** Be sure to warm up the Detector for 10 minutes and clean the glass filter of emitter and receiver before calibration.Calibration procedure for #1 axis.(1)Place the Gauge Pin Unit Fixture into the Detector with "arrow" mark setting to the #1 axis. (ref. Fig.). (2)Set Variation Detecting Level Setter at "1.00". (3)Insert the point of Gauge Pin Unit into the center of detecting area smoothly and quickly but in the horizontal manner against the detecting area. (4)While repeating the insertion, adjust #1 axis Gain Adjustment VR at the minimum level where Variation Detection Alarm Lamp turns on at the time when the point of Gauge Pin Unit is inserted. * The Variation Detection Alarm Lamp would turn on occasionally when the point of Gauge Pin Unit is pulled out, but this phenomenon shall be ignored. * While repeating the insertion, take interval of 3 seconds after Variation Detection Alarm Lamp turns off. * Sensitivity comes up by turning Gain Adjustment VR clockwise and comes down by turning it anti-clockwise. (5)Set Variation Detecting Level Setter at "1.03". (6)Repeat the insertion and adjust #1 axis Gain Adjustment VR at the level where Variation Detection Alarm Lamp does not turn on at the time when the point of Gauge Pin Unit is inserted. (7)Repeat the procedure (2) through (6). And, the calibration has been finished properly if Variation Detection Alarm Lamp turns on at the level "1.00" and turns off at the level "1.03". Follow the above procedure to calibrate other axes, placing Gauge Pin Unit Fixture into the Detector with "arrow" mark setting to the axis to be calibrated.
Fig.

 

Dưỡng Kiểm Ren Plug Gauge OSG

Dưỡng Kiểm Ren Plug Gauge OSG...
Liên hệ:

Số người đã mua:

Dưỡng Đo Ba Dây Eisen TW

...
Liên hệ:

Số người đã mua:

Dưỡng Ren Trục Sokuhansha - SHS

...
Liên hệ:

Số người đã mua:

Máy Đo Hiệu Chuẩn Takikawa TMG

...
Liên hệ

Số người đã mua:

Messenger Zalo gg-map sms hotline